3M表面采样棒UXL100使用说明书，常备现货，3M Client Trace ATP
3M表面采样棒UXL100使用说明书，常备现货，3M Client Trace ATP
3M表面采样棒UXL100使用说明书，常备现货，3M Client Trace ATP
商品描述：
3M表面采样棒UXL100，是一种型一体化的快速检测、样品采集和反应装置，配套ATP荧光检测仪使用。
本公司采用的液态稳定试剂，易于使用，能够提供准确、发光信号持续时间久和重复性好的检测结果。
ATP荧光检测仪，利用ATP荧光检测原理检测所有的真菌、细菌、藻菌、需氧菌、自氧、醋酸杆菌、亚硫酸细菌、霉菌等，
广泛应用于食品加工业、餐饮行业、医疗卫生行业、环保及其它执法部门等。
ATP表面采样棒结构：
ATP荧光检测拭子主要由密封帽、密封管及棉签三部分组成。
3M表面采样棒UXL100产品特点：
1.适用范围：物体表面。
2.包装：20支/包、5包/盒
3.储存：0至-4℃冷藏保存10个月。
4.特点：快速、准确、环保。
3M表面采样棒UXL100操作流程如下：
1.将冷藏或冷冻条件下的拭子在室温下放置约10分钟。
2.用一只手捏紧，另一只手轻旋密封管将其拔出（切勿直接将密封管拔出！）。
3.用棉头均匀擦拭物体表面成Z字形约10*10cm2，或将其浸入待测液体之后快速拿出。完成后，将密封管套上。
4.将密封杆折断，使其中所盛溶液顺进液孔，全部流到棉头，摇晃拭子底部约2秒。
5.将拭子快速放入ATP荧光检测仪，摁下OK键，15或10秒后即可读数。
1、3M Clean-Trace
水质采样棒-总数ATP 型号：AQT100螺纹设计，提高采样的精度,可以同时测出细胞外和细胞内的ATP总量UXL100表面采样棒 3M Clean-Trace ATP表面采样棒，10支/包，10包/箱，适合3M Clean-Trace ATP荧光检测仪表面采样检测用，属于一次性耗材。
2、3M Clean-Trace阳性对照 型号：HWATP10用于定期对ATP检测仪及采样棒的校正，从而确保检测系统的有效性,对Clean-Trace 表面采样棒，Clean-Trace水质采样棒采用不同设计,操作简便，快速.
3、3M Clean-Trace水质ATP试剂盒试管 型号：BTCUV
4、3M Clean-Trace表面采样棒阳性对照 3ngATP 型号：ATP10
5、3M Clean-Trace水质采样棒阳性对照 3ngATP，CIP清洗水适用 型号：LWATP10
6、3M Clean-Trace水质采样棒CIP检测阳性对照 3ngATP工业水适用 型号： HWATP10
7、3M Clean-Trace水质ATP测试盒 型号：ULW10
针对工业用水，废水处理，水冷却系统等领域的ATP检测而设计，可用于判读这些系统中微生物的数量水平，以衡量消灭细菌剂使用效果UXL100表面采样棒 Clean-Trace 表面采样棒。8、3M Clean-Trace 水质采样棒-游离ATP 型号：AQT100
螺纹设计，提高采样的精度，针对细胞外游离ATP检测，与总数ATP配合使用，可以快速检测消毒效果。9、3M Clean-Trace水质ATP试剂盒支架 型号：NHT01
10、3M Clean-Trace表面蛋白测试棒 型号：PRO100
11、3M Clean-Trace表面过敏原测试棒 型号：ALLTEC60
ATP检测试剂盒|阴/阳性校准控制棒PCD4000|SPXL1333通用型水样检测拭子|NG3荧光检测仪
3M Clean‐Trace Hygiene Management System for Environmental Surfaces
Contaminated environmental surfaces are an important source for transmission of healthcare‐
associated infections. Healthcare workers can contaminate their hands by touching contaminated
surfaces and then transfer pathogens to their patients. The maintenance of a clean environment is
an important factor in reducing the risk of cross contamination. Unmonitored organic residues can
build up to high levels on surfaces if adequate cleaning procedures are not implemented. Surfaces,
although appearing visibly clean, can still harbor significantly high levels of contamination.
The 3M Clean‐Trace Hygiene Management System provides an objective and quantifiable “real‐
time” approach to assess and measure cleaning efficacy. The system is based on the measurement
of levels of ATP present on an environmental surface. ATP is the molecule that provides energy for
cellular metabolism and is present in all living cells. It is present in any organic residue, e.g. body
fluids, skin cells and microorganisms, making ATP an excellent marker for organic contamination or
contamination from a biological source.
A 3M Clean‐Trace ATP Surface Test is used to swab a selected test point. The test is activated and
the swab is brought into contact with the test enzyme solution. The test is then placed in the 3M
Clean‐Trace Luminometer. This measures the light generated by the enzyme solution and
produces a result expressed in Relative Light Units (RLUs). The greater the level of ATP present on
the swab, the greater the amount of light generated by the test and consequently, the higher the
RLU level produced.
The 3M Clean‐Trace ATP Surface Test can be performed in less than 30 seconds, providing a real‐
time result that indicates the cleanliness of the surface tested. This provides an opportunity to take
any corrective action required such as re‐cleaning and re‐testing the surface.
